Top tips for cleaning your Brompton
Wash your Brompton bike
-
Use a sponge, some warm water and some specific bike cleaner. Your local Brompton dealer should be able to recommend a suitable bike detergent.
-
Don’t use household dishwashing detergent, it has got lots of salt in it which won’t do your Brompton any good.
-
Don’t use a hose or Jet-wash to clean your bike, this will force water into areas like the hubs, hinges and headset, pushing out the grease inside and damaging bearings.
-
Give the frame parts, wheels and underside of the bike (where dirt will mostly accumulate) a thorough clean.
If your bike has a Sturmey Archer hub, be careful to ensure no water enters the drive-side axle end (where the gear indicator chain enters the hub) as this will become trapped inside the hub and cause corrosion.
Wheels and Tyres
Use a stiff brush to clean the wheel rims and tires, removing any brake residue that will have accumulated. The black residue that accumulates on the rims is a mixture of dirt, pad material and aluminum powder worn from the braking surface of the rim, this residue is abrasive and will accelerate the wear of the rim and pads. When cleaning the pads and rims check to ensure they are not worn out and a worn rim or pads should be replaced immediately. Make sure you rinse the soapy water off the wheels with some clean cold water.
Inspect your tires for wear and remove any bits of grit and debris that might have become embedded in the tread. Also check the sidewalls for damage, if the tread or sidewalls are damaged or the tread excessively worn replace the tire. Check your tire pressure and adjust if needed.
The recommended pressure range for each of the tires we supply is shown in the table below:
Seatpost
Make sure your seatpost clean as any contamination on the post or the sleeve inside the frame can make the post slip down when riding and might make it difficult to raise and lower the post when folding/unfolding the bike. It is worth remembering that many cleaning products will leave a residue that can cause similar problems so rinse thoroughly with clean water.
Drivetrain
The chain, chainring and sprockets will need cleaning to remove any accumulated dirt and lubricant, before a fresh application of chain lubricant. Your Brompton dealer will be able to recommend a degreaser or chain cleaning detergent to use. When spraying the drivetrain ensure you do not get the cleaner onto other parts of the bike.
If your bike was made after December 2011 your chain will have a SRAM powerlink fitted and you can easily remove the chain to clean it. If the chain is not fitted with a powerlink you can clean it (along with the chainring and sprockets in situ). Using your chosen cleaning fluid and a stiff brush ensure that the chain, chainring, tensioner idlers and sprockets are clean. If you have a 2 or 6-speed bike, you can use a small flat-head screwdriver to remove any compacted dirt from between the two sprockets and from the chain tensioner idlers. Once the drivetrain is clean rinse with water to remove the cleaning fluid and then allow the drivetrain to dry.
When the chain is cleaned and dry you can apply fresh lubricant. The best method is to carefully apply one drop of lubricant to each roller, this will take a little longer than just squirting lube on the chain while backpedaling but will ensure the lube gets where it’s needed and nowhere else. Once you have applied the lube, spin the pedal backward for several revolutions to allow the lubricant to work into the rollers, before wiping off any excess lubricant from the chain with a cloth.
If the chain is skipping over the rear sprocket/sprockets under load it is likely that the chain is worn and the drivetrain components will need replacing.
Brake calipers
Once the bike is clean you should apply a little lubricant (chain lubricant is ideal) to the pivot points and spring bush on the brake caliper, as well as to the brake cable. When doing this it is extremely important that you do not get any lubricant on the brake pads or rims, should this happen clean the brake pads and rims thoroughly with a degreaser before attempting to ride the bike.
Hinges
Apply a couple of drops of chain lube to the mainframe and handlebar support hinges on the mating surfaces between the two parts of the hinge. Open and close the hinges several times to allow the lube to get between the surfaces and wipe away any excess.
To finish, wipe off your bike with a microfibre cloth and you are then ready to ride!
